![altium designer 18 automatically adjust when devices overlap altium designer 18 automatically adjust when devices overlap](https://venturebeat.com/wp-content/uploads/2018/06/Screen-Shot-2018-06-28-at-8.27.56-AM-e1530189460758.jpg)
Name – normally, component pin names are displayed inside the body of the component adjacent to the corresponding pin.The setting will be applied to all currently open sheets. Numeric, separated by a colon ':' – choose this option to use a numeric suffix with a colon separator (e.g., R12:1, R12:2, R12:3).Numeric, separated by a dot '.' – choose this option to use a numeric suffix with a dot separator (e.g., R12.1, R12.2, R12.3).Alpha – choose this option to use an alphabetic suffix with no separator (e.g., R12A, R12B, R12C).Use this drop-down to choose how the suffix is presented: Notes – enable this option to include Notes in the clipboard.Įach part in a multi-part schematic component is uniquely identified by an alphabetic or numeric suffix.Parameter Sets – enable this option to include Parameter Sets in the clipboard.No ERC Markers – enable this option to include No ERC Markers in the clipboard/.Options include: Smallest, Small, Medium, and Large. Drag Step – select the desired size from the drop-down.Click the check box to toggle its status. If this option is disabled, wiring dragged with a component will be repositioned obliquely. Drag Orthogonal – if this option is enabled, when you drag components, any wiring that is dragged with the component is kept orthogonal (i.e., corners at 90 degrees).Unconnected Left To Right – enable this option and those unconnected ports on a schematic document are displayed in a left to right direction (as a right style).Port Direction – enable this option to allow port styles to be determined by the I/O type attribute of corresponding ports.Sheet Entry Direction – enable this option to display the direction of sheet entries on a schematic document.The pin direction is indicated by the orientation of a triangle symbol. Pin Direction – enable this option to display the direction of pins of components on a schematic document.Display Cross-Overs – when this option is enabled, the wiring cross-overs will be displayed with small bridges on the currently focused schematic sheet.Convert Cross-Junctions – enabling this option denotes that when the addition of a wire would create a four-way junction, it is instead converted into two adjacent three-way junctions. Disabling this option denotes that when a four way junction is created, the two wires crossing at the intersection are not joined electrically and if the Display Cross Overs option is enabled, a cross-over is shown on this intersection.You can only graphically move this text field. After focusing on the field you want to modify, click it again or press the F2 shortcut key to open the field for editing. If this option is not enabled, you cannot edit the text directly and you have to edit it from the Parameter Properties dialog. Enable In-Place Editing – if this option is enabled, the focused text field may be directly edited within the Schematic Editor rather than in a dialog box.You will need to enable the Optimize Wires & Buses option first. The wire is then cut into two segments and the segments are terminated onto any two hot pins of the component automatically. Components Cut Wires – enable this option to drop a component onto a schematic wire.You need to enable this option to have the ability to automatically cut a wire and terminate onto any two pins of this component when this component is dropped onto this wire. Overlapping wires, poly-lines, or buses are removed automatically. Optimize Wires & Buses – enable this option to prevent extra wires, poly-lines, and buses from overlapping on top of each other. Break Wires At Autojunctions – enable this option to break wires at autojunctions (autojunctions are automatically inserted when two wires/buses/signal harnesses are connected in a T-type fashion or when a wire/bus/signal harness connects orthogonally to a pin or power port/bus power port).Select Mils or Millimeters, whichever is desired.The Schematic – General page is part of the main Preferences dialog that is accessed by clicking the control in the upper-right corner of the design space then selecting the General entry under the Schematic folder. The Schematic – General page of the Preferences dialog SummaryĪs its name suggests, the Schematic – General page of the Preferences dialog provides numerous general controls related to editing schematic-based documents directly in the design space. Parent page: Accessing, Defining & Managing System Preferences